Difference between revisions of "Arm trace technical specification"

From SEGGER Wiki
Jump to: navigation, search
(Minimum for buffer trace)
(Arm trace timing requirements)
 
(5 intermediate revisions by the same user not shown)
Line 1: Line 1:
When using the J-Trace PRO as a debugging tool it is crucial for a successful session that the trace data output by the microcontroller is meeting specific timing requirements. The trace clock speed (TRACECLK) is on most microcontrollers directly dependent on the CPU clock speed and is usually half of the CPU clock speed.
+
When using the J-Trace PRO as a debugging tool it is crucial for a successful session that the trace data output by the microcontroller is meeting specific timing requirements. The trace clock speed (TRACECLK) is on most microcontrollers directly dependent on the CPU clock speed and is usually half of the CPU clock speed. The following article will show the Arm trace timing requirements and which Arm Coresight components are required for which type of instruction tracing.
   
 
__TOC__
 
__TOC__
Line 36: Line 36:
   
 
According to specification the maximum in spec trace clock is 100 MHz. But as there are some target devices that support even higher trace clock signals than that J-Trace Pro also supports higher trace clock speeds as explained in the note above.
 
According to specification the maximum in spec trace clock is 100 MHz. But as there are some target devices that support even higher trace clock signals than that J-Trace Pro also supports higher trace clock speeds as explained in the note above.
  +
  +
{{Note|1=This trace specification assumes that all [[UM08001_J-Link_/_J-Trace_User_Guide#19-pin_JTAG.2FSWD_and_Trace_connector | 4 data pins]] are used in the trace interface. Only then an overflow free transmission can be guaranteed. Selecting 1 or 2 data pins to save pins can cause overflows depending on how much trace data the target application is creating. So it is recommended to use 4 data pins in your board design.}}
   
 
== Solution for out of spec signals ==
 
== Solution for out of spec signals ==
Line 48: Line 50:
 
=== Minimum for pin tracing ===
 
=== Minimum for pin tracing ===
 
* Trace pins + [[UM08001_J-Link_/_J-Trace_User_Guide#19-pin_JTAG.2FSWD_and_Trace_connector | trace connector]]
 
* Trace pins + [[UM08001_J-Link_/_J-Trace_User_Guide#19-pin_JTAG.2FSWD_and_Trace_connector | trace connector]]
* [[ETM]] or PTM
+
* [[ETM]] or [[PTM]]
* TPIU
+
* [[TPIU]]
   
 
=== Optional for both setups ===
 
=== Optional for both setups ===
* Trace funnel
+
* [[Trace funnel]]
   
 
=== Special case Cortex-M0+ trace ===
 
=== Special case Cortex-M0+ trace ===

Latest revision as of 08:38, 13 October 2022

When using the J-Trace PRO as a debugging tool it is crucial for a successful session that the trace data output by the microcontroller is meeting specific timing requirements. The trace clock speed (TRACECLK) is on most microcontrollers directly dependent on the CPU clock speed and is usually half of the CPU clock speed. The following article will show the Arm trace timing requirements and which Arm Coresight components are required for which type of instruction tracing.

Arm trace timing requirements

Arm defines the trace timing requirements as follows:

Trace timing diagram with CPU clock, TRACECLK and Trace data
Timing variables and values
Signal name Description Value
twl TRACECLK LOW pulse width Min. 2 ns
twh TRACECLK HIGH pulse width Min. 2 ns
tr/tf Clock and data rise/fall time Max. 3 ns
ts Data setup time Min. 3 ns
th Data hold time Min. 2 ns

Note: J-Trace PRO has been designed to work with min. 1 ns ts and min. 1 ns th.

According to specification the maximum in spec trace clock is 100 MHz. But as there are some target devices that support even higher trace clock signals than that J-Trace Pro also supports higher trace clock speeds as explained in the note above.

Note:
This trace specification assumes that all 4 data pins are used in the trace interface. Only then an overflow free transmission can be guaranteed. Selecting 1 or 2 data pins to save pins can cause overflows depending on how much trace data the target application is creating. So it is recommended to use 4 data pins in your board design.

Solution for out of spec signals

In some rare cases devices supporting Embedded Trace Macrocell (ETM) trace are not outputting signals that fulfill the aforementioned timing requirements. To still make trace debugging available to the customer the J-Trace PRO has a so called Trace timing configuration feature which compensates wrongly output trace data signals.

Required trace components

Minimum for buffer trace

Minimum for pin tracing

Optional for both setups

Special case Cortex-M0+ trace