Difference between revisions of "Main Page"
(→IDE and Debugger specifics) |
(→J-Trace) |
||
| Line 169: | Line 169: | ||
=== J-Trace === |
=== J-Trace === |
||
* [[General information about tracing]] |
* [[General information about tracing]] |
||
| + | * [[How to configure JLinkScript files to enable tracing]] |
||
* [[Tracing on Atmel ATSAMA5D2]] |
* [[Tracing on Atmel ATSAMA5D2]] |
||
* [[Tracing on Atmel ATSAME54]] |
* [[Tracing on Atmel ATSAME54]] |
||
Revision as of 10:34, 27 March 2018
Welcome to the SEGGER - Support Wiki
Contents
Debug Probes - J-Link & J-Trace
J-Link
Troubleshooting
- Debug session does not start
- J-Link cannot connect to the CPU
- Could not open J-Link shared library
- J-Link shown as generic BULK device in Windows
- J-Link-OB SAM3U
- J-Link-OB-RX621-ARM-SWD
- SPI Flash
- Unlimited Number of Breakpoints in Flash
- Debugging self-modifying code in flash
- Cannot update firmware of Flasher Portable
- Manual setup of JTAG chain
- Access to illegal addresses causes core to crash
- J-Trace PRO USB driver problems
- J-Link no USB enumeration
- J-Link LITE incorrectly shown as SAM-ICE
IDE and Debugger specifics
- SEGGER Embedded Studio
- ETB trace on NXP TWR-K65F
- How to port projects from IAR EWARM to SEGGER Embedded Studio
- How to configure Embedded Studio to use SWO
- Embedded Studio VCS configuration
- Embedded Studio installation on newer Linux versions
- How to enable RTOS thread awarness
- How to copy ROM sections into RAM sections during run time
- How to use an external toolchain with Embedded Studio
- SEGGER Ozone
- TI Code Composer Studio
- IAR EWARM
- Keil MDK-ARM
- J-Link Commander
Device specifics
Ambiq Micro
Analog Devices
Atmel
Infineon
Intel
Nordic Semi
NXP
Renesas
Silicon Labs
ST
- Connecting to STM32 Nucleo boards
- Using SWO on STM327xxG evaluation boards
- Setting read out protection on STM32F0 devices
- Secured ST device detected
- SPC560D-Discovery Evalboard
- STR91x
- STM32
TI
Toshiba
Evaluation board specifics
Ambiq Micro
Adafruit
Atmel
Infineon
Microchip
Renesas
SiFive
Silicon Labs
TI
NXP
ST
Open Flashloader
J-Trace
- General information about tracing
- How to configure JLinkScript files to enable tracing
- Tracing on Atmel ATSAMA5D2
- Tracing on Atmel ATSAME54
- Tracing on Atmel ATSAME70
- Tracing on Atmel ATSAMV71
- Tracing on Infineon XMC4400 series MCUs
- Tracing on Infineon XMC4500 series MCUs
- Tracing on Nordic Semiconductor nRF52
- Tracing on NXP LPC1768
- Tracing on NXP LPC1788
- Tracing on NXP LPC1857
- Tracing on NXP LPC4357
- Tracing on NXP Kinetis MK21FN1M0
- Tracing on NXP Kinetis MK40
- Tracing on NXP Kinetis MK60N512
- Tracing on NXP Kinetis MK64FN1M0
- Tracing on NXP Kinetis MK66FN2M0 (SEGGER emPower Board)
- Tracing on NXP Kinetis MK70FN1M0
- Tracing on NXP Kinetis MK80FN2
- Tracing on NXP Kinetis MKV58F1M0
- Tracing on NXP Kinetis MKW24D512
- Tracing on Renesas Synergy R7FS7G2
- Tracing on Renesas R7S721001WS (RZ/A1H)
- Tracing on Renesas R7S910017 (RZ/T1)
- Tracing on Silicon Labs EFM32GG11B
- Tracing on Silicon Labs EFM32GG990
- Tracing on Silicon Labs EFM32PG12
- Tracing on Silicon Labs EZR32LG330
- Tracing on Silicon Labs EZR32WG330
- Tracing on ST STM32F107
- Tracing on ST STM32F207
- Tracing on ST STM32F303
- Tracing on ST STM32F407 (SEGGER Cortex-M Trace Reference Board)
- Tracing on ST STM32F417
- Tracing on ST STM32F429
- Tracing on ST STM32F437
- Tracing on ST STM32F439
- Tracing on ST STM32F446
- Tracing on ST STM32F746
- Tracing on ST STM32F756
- Tracing on ST STM32F767
- Tracing on ST STM32F769
- Tracing on ST STM32H743
- Tracing on ST STM32H753
- Tracing on ST STM32L476
- Tracing on ST STM32L4R
- Tracing on ST STM32L4S
- Tracing on ST STM32L152
- Tracing on TI MSP432E4
- Tracing on TI TM4C129
- Tracing on Toshiba TMPM370
- Tracing on Toshiba TMPM440
- Getting unknown addresses in instruction trace
Keil MDK
Getting Started with Various IDEs
Miscellaneous
Glossary / Definitions
J-Link software
- J-Link Software and Documentation Pack
- Enable J-Link log file
- Using J-Link Script Files
- Using J-Link Command Strings
- Read-Modify-Write Flash
- Using J-Link VCOM functionality
- J-Link Commander
- RTT
- Memory accesses
- Setting up Ethernet interface
