Difference between revisions of "Mindmotion-MB-036"
(Created page with "__TOC__ This article describes specifics for the Mindmotion PLUS5270 MM32F5270 evaluation board. 450px == Minimum requirements == *...") |
|||
(6 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
__TOC__ |
__TOC__ |
||
− | This article describes specifics for the Mindmotion |
+ | This article describes specifics for the Mindmotion MB-036 evaluation board. |
− | [[File: |
+ | [[File:MM-MB-036-board.jpg|450px]] |
== Minimum requirements == |
== Minimum requirements == |
||
− | * J-Link software V7. |
+ | * J-Link software V7.82e or later |
== Preparing for J-Link == |
== Preparing for J-Link == |
||
− | *Connect the J-Link |
+ | *Connect the J-Link: VTref= CN9-32(64 on PCB) / GND=CN9-31(63 on PCB) / SWDIO=CN9-14(46 on PCB) / SWDCLK=CN9-17(49on PCB) |
− | *Power the board via |
+ | *Power the board via USB (CN2) |
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
||
− | [[File: |
+ | [[File:MM_MB-036_MM32F3270G7P_Connect.png|400px]] |
== Example Project== |
== Example Project== |
||
− | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the Mindmotion |
+ | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the Mindmotion MB-036 MM32F3277G7P. <br> |
It is a simple Hello World sample linked into the internal flash.<br> |
It is a simple Hello World sample linked into the internal flash.<br> |
||
====SETUP==== |
====SETUP==== |
||
− | *J-Link software: V7. |
+ | *J-Link software: V7.82e |
*Embedded Studio: V6.34 |
*Embedded Studio: V6.34 |
||
− | *Hardware: Mindmotion |
+ | *Hardware: Mindmotion MB-036 |
− | *Link: [[File: |
+ | *Link: [[File:MM_MM32-036_MM32F3277G7P_TestProject_ES_V634.zip]] |
Latest revision as of 16:39, 9 December 2022
This article describes specifics for the Mindmotion MB-036 evaluation board.
Minimum requirements
- J-Link software V7.82e or later
Preparing for J-Link
- Connect the J-Link: VTref= CN9-32(64 on PCB) / GND=CN9-31(63 on PCB) / SWDIO=CN9-14(46 on PCB) / SWDCLK=CN9-17(49on PCB)
- Power the board via USB (CN2)
- Verify the Connection with e.g. J-Link Commander. The output should look as follows:
Example Project
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the Mindmotion MB-036 MM32F3277G7P.
It is a simple Hello World sample linked into the internal flash.
SETUP
- J-Link software: V7.82e
- Embedded Studio: V6.34
- Hardware: Mindmotion MB-036
- Link: File:MM MM32-036 MM32F3277G7P TestProject ES V634.zip