Difference between revisions of "Raspberry Pi Pico"
| Line 38: | Line 38: | ||
</ol> |
</ol> |
||
'''Note:''' For a more reliable, simpler solution, the [https://www.segger.com/products/debug-probes/j-link/accessories/adapters/segger-flying-wire-adapter/ SEGGER Flying Wire Adapter] is recommended. |
'''Note:''' For a more reliable, simpler solution, the [https://www.segger.com/products/debug-probes/j-link/accessories/adapters/segger-flying-wire-adapter/ SEGGER Flying Wire Adapter] is recommended. |
||
| + | |||
| + | ==Example Projects== |
||
| + | To run the following example projects the following prerequisites need to be met: |
||
| + | * [https://www.segger.com/downloads/jlink/#J-LinkSoftwareAndDocumentationPack J-Link software] V6.98c or later |
||
| + | * J-Link HW revision 11 or later (J-Link Edu Mini and J-Trace Pro V1 or later also supported) |
||
| + | * [https://www.segger.com/products/development-tools/embedded-studio/ SEGGER Embedded Studio] V5.40c or later |
||
| + | * [https://www.segger.com/products/development-tools/ozone-j-link-debugger/ Ozone] V3.22c or later |
||
| + | |||
| + | ===RAM Projects=== |
||
| + | |||
| + | Core0: [[Media:Raspberry_RP2040_Pico_RAM_Core0.zip|Raspberry_RP2040_Pico_RAM_Core0.zip]] |
||
| + | |||
| + | Core1: [[Media:Raspberry_RP2040_Pico_RAM_Core1.zip|Raspberry_RP2040_Pico_RAM_Core1.zip]] |
||
| + | |||
| + | ===Flash Projects=== |
||
Revision as of 12:26, 22 March 2021
The Raspberry Pi Pico is a Raspberry Pi RP2040 evaluation board. It is the first MCU evaluation board published by Raspberry Pi.
Contents
Features (selection)
- RP2040 MCU
- 2MB on board QSPI flash
- Micro USB-B 1.1
- Temperature sensor
- On board LED
- external debug connector pads
For further information please refer to the Rapberry Pi Pico web page
Setting up with J-Link
The Raspberry Pi Pico evaluation board comes with an external SWD debug connector (3 pins: SWCLK, GND, SWDIO). To set the board up with J-Link, the following steps are required:
- Solder a 3-pin pin strip to the debug connector pads.
-
Solder a pin Strip to the GPIO pads of the evaluation board. The relevant pad is Pad 36 (3V3(OUT))
-
Connect the J-Link to the evaluation board, using jumper wires as follows:
Pin RP Pico Pin J-Link Signal "DEBUG" "SWCLK" 9 SWCLK "DEBUG" "GND" 4 GND "DEBUG" "SWDIO" 7 SWDIO "3V3" Pad 36 1 VTref
Note: For a more reliable, simpler solution, the SEGGER Flying Wire Adapter is recommended.
Example Projects
To run the following example projects the following prerequisites need to be met:
- J-Link software V6.98c or later
- J-Link HW revision 11 or later (J-Link Edu Mini and J-Trace Pro V1 or later also supported)
- SEGGER Embedded Studio V5.40c or later
- Ozone V3.22c or later
RAM Projects
Core0: Raspberry_RP2040_Pico_RAM_Core0.zip
Core1: Raspberry_RP2040_Pico_RAM_Core1.zip
