Difference between revisions of "STM32H743I-EVAL"
(→Sample projects) |
|||
Line 1: | Line 1: | ||
__TOC__ |
__TOC__ |
||
+ | This article describes specifics for the ST STM32H743I-EVAL evaluation board.<br> |
||
− | = SWO = |
||
+ | [[File:ST_STM32H743I-EVAL.jpg|450px]] |
||
+ | |||
+ | == Preparing for J-Link == |
||
+ | *Connect the J-Link to ...... |
||
+ | *Power the board via........ |
||
+ | * Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
||
+ | [[File:ST_STM32H743I-EVAL_CONNECT.PNG|400px]] |
||
+ | |||
+ | == Example Project== |
||
+ | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the [SiliconVendor] [EvalBoardName].<br>It is a simple Hello World sample linked into the internal flash.<br> |
||
+ | ====SETUP==== |
||
+ | *J-Link software: V7.86d |
||
+ | *Embedded Studio: V7.10 |
||
+ | *Hardware: ST STM32H743I-EVAL |
||
+ | *Link: [[File:ST_STM32H743I-EVAL_TestProject_ES_V710.zip]] |
||
+ | |||
+ | == SWO == |
||
SWO is supported on the STM32H743I-EVAL. |
SWO is supported on the STM32H743I-EVAL. |
||
− | == Requirements == |
+ | === Requirements === |
In order to make SWO working correctly, min. J-Link software V6.34 is required. Previous versions are not guaranteed to work correctly with SWO. |
In order to make SWO working correctly, min. J-Link software V6.34 is required. Previous versions are not guaranteed to work correctly with SWO. |
||
− | == Sample projects == |
+ | === Sample projects === |
The following sample projects that demonstrate SWO on the STM32H743I-EVAL are available: |
The following sample projects that demonstrate SWO on the STM32H743I-EVAL are available: |
||
Revision as of 16:34, 21 March 2023
Contents
This article describes specifics for the ST STM32H743I-EVAL evaluation board.
Preparing for J-Link
- Connect the J-Link to ......
- Power the board via........
- Verify the Connection with e.g. J-Link Commander. The output should look as follows:
Example Project
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the [SiliconVendor] [EvalBoardName].
It is a simple Hello World sample linked into the internal flash.
SETUP
- J-Link software: V7.86d
- Embedded Studio: V7.10
- Hardware: ST STM32H743I-EVAL
- Link: File:ST STM32H743I-EVAL TestProject ES V710.zip
SWO
SWO is supported on the STM32H743I-EVAL.
Requirements
In order to make SWO working correctly, min. J-Link software V6.34 is required. Previous versions are not guaranteed to work correctly with SWO.
Sample projects
The following sample projects that demonstrate SWO on the STM32H743I-EVAL are available:
This example project does not require any extra settings by the user. The SWO stream can be viewed with e.g. J-Link SWO Viewer which is included in the J-Link Software and Documentation Pack and is available for free. This project was created with Embedded Studio V3.40.
- IAR EWARM 8.22 sample project
- Note: IAR does not handle the special setup needed for this particular target device automatically so SWO printf will only work when using Ozone. The example project contains a Ozone configuration that will work out-of-the-box.