Difference between revisions of "Tracing on NXP Kinetis MK66FN2M0 (SEGGER emPower Board)"

From SEGGER Wiki
Jump to: navigation, search
(Streaming trace)
Line 6: Line 6:
 
= Minimum requirements =
 
= Minimum requirements =
 
In order to use trace on the NXP Kinetis MK66FN2M0 MCU devices, the following minimum requirements have to be met:
 
In order to use trace on the NXP Kinetis MK66FN2M0 MCU devices, the following minimum requirements have to be met:
* J-Link software version V6.14a or later
+
* J-Link software version V6.18c or later
* Ozone V2.22o or later (if streaming trace and / or the sample project from below shall be used)
+
* Ozone V2.46a or later (if streaming trace and / or the sample project from below shall be used)
 
* J-Trace PRO for Cortex-M HW version V1.0 or later
 
* J-Trace PRO for Cortex-M HW version V1.0 or later
   
Line 14: Line 14:
 
The following sample project is designed to be used with J-Trace PRO and Ozone to demonstrate streaming trace. The project has been tested with the minimum requirements mentioned above and a [https://www.segger.com/empower.html SEGGER emPower Evalboard]. The sample project comes with a pre-configured project file for Ozone that runs out-of-the box. In order to rebuild the sample project, [https://www.segger.com/embedded-studio.html SEGGER Embedded Studio] can be used.
 
The following sample project is designed to be used with J-Trace PRO and Ozone to demonstrate streaming trace. The project has been tested with the minimum requirements mentioned above and a [https://www.segger.com/empower.html SEGGER emPower Evalboard]. The sample project comes with a pre-configured project file for Ozone that runs out-of-the box. In order to rebuild the sample project, [https://www.segger.com/embedded-studio.html SEGGER Embedded Studio] can be used.
   
[[Media:NXP_Kinetis_MK66FN2M0_TraceExample_90MHz_TCLK.zip | NXP_Kinetis_MK66FN2M0_TraceExample_90MHz_TCLK.zip]]
+
[[Media:NXP_Kinetis_MK66FN2M0_TraceExample_90MHz_TCLK_2.zip | NXP_Kinetis_MK66FN2M0_TraceExample_90MHz_TCLK.zip]]
   
 
= Tested Hardware =
 
= Tested Hardware =

Revision as of 16:03, 20 September 2017

This article describes how to get started with trace on the NXP Kinetis MK66FN2M0 MCU. This article assumes that there is already a basic knowledge about trace in general (what is trace, what different implementations of trace are there, etc.). If this is not the case, we recommend to read Trace chapter in the J-Link User Manual (UM08001). The NXP Kinetis MK66FN2M0 MCU implements tracing via pins, so a J-Trace can be used for tracing.

Minimum requirements

In order to use trace on the NXP Kinetis MK66FN2M0 MCU devices, the following minimum requirements have to be met:

  • J-Link software version V6.18c or later
  • Ozone V2.46a or later (if streaming trace and / or the sample project from below shall be used)
  • J-Trace PRO for Cortex-M HW version V1.0 or later

Sample project

Streaming trace

The following sample project is designed to be used with J-Trace PRO and Ozone to demonstrate streaming trace. The project has been tested with the minimum requirements mentioned above and a SEGGER emPower Evalboard. The sample project comes with a pre-configured project file for Ozone that runs out-of-the box. In order to rebuild the sample project, SEGGER Embedded Studio can be used.

NXP_Kinetis_MK66FN2M0_TraceExample_90MHz_TCLK.zip

Tested Hardware

SEGGER emPower