Difference between revisions of "Tracing on Renesas Synergy R7FS5D5"
(Created page with "__TOC__ This article describes how to get started with trace on the Renesas Synergy R7FS5D5 MCU. This article assumes that there is already a basic knowledge about trace in g...") |
(→Sample project) |
||
| Line 10: | Line 10: | ||
* J-Trace PRO for Cortex-M HW version V1.0 or later |
* J-Trace PRO for Cortex-M HW version V1.0 or later |
||
| − | = Sample |
+ | = Sample projects = |
| + | |||
| + | == ETB == |
||
| + | The following sample project is designed to be used with any J-Link or J-Trace debug probe and Ozone to demonstrate ETB trace. The project has been tested with the minimum requirements mentioned above on a Synergy TB-S5D5 equipped with a R7FS5D5 MCU. The sample project comes with a pre-configured project file for Ozone that runs out-of-the box. In order to rebuild the sample project, [https://www.segger.com/embedded-studio.html SEGGER Embedded Studio] can be used. |
||
| + | |||
| + | [[Media:Renesas_Synergy_S5D5_ETB_Trace.zip | Renesas_Synergy_S5D5_ETB_Trace.zip]] |
||
| + | |||
== Streaming trace == |
== Streaming trace == |
||
The following sample project is designed to be used with J-Trace PRO and Ozone to demonstrate streaming trace. The project has been tested with the minimum requirements mentioned above and a ''Synergy TB-S5D5'' eval board. The sample project comes with a pre-configured project file for Ozone that runs out-of-the box. In order to rebuild the sample project, [https://www.segger.com/embedded-studio.html SEGGER Embedded Studio] can be used. |
The following sample project is designed to be used with J-Trace PRO and Ozone to demonstrate streaming trace. The project has been tested with the minimum requirements mentioned above and a ''Synergy TB-S5D5'' eval board. The sample project comes with a pre-configured project file for Ozone that runs out-of-the box. In order to rebuild the sample project, [https://www.segger.com/embedded-studio.html SEGGER Embedded Studio] can be used. |
||
Revision as of 16:44, 19 December 2018
This article describes how to get started with trace on the Renesas Synergy R7FS5D5 MCU. This article assumes that there is already a basic knowledge about trace in general (what is trace, what different implementations of trace are there, etc.). If this is not the case, we recommend to read Trace chapter in the J-Link User Manual (UM08001). The Renesas Synergy R7FS5D5 MCU implements tracing via pins , so a J-Trace can be used for tracing.
Minimum requirements
In order to use trace on the Renesas Synergy R7FS5D5 devices, the following minimum requirements have to be met:
- J-Link software version V6.40 or later
- Ozone V2.60h or later (if streaming trace and / or the sample project from below shall be used)
- J-Trace PRO for Cortex-M HW version V1.0 or later
Sample projects
ETB
The following sample project is designed to be used with any J-Link or J-Trace debug probe and Ozone to demonstrate ETB trace. The project has been tested with the minimum requirements mentioned above on a Synergy TB-S5D5 equipped with a R7FS5D5 MCU. The sample project comes with a pre-configured project file for Ozone that runs out-of-the box. In order to rebuild the sample project, SEGGER Embedded Studio can be used.
Renesas_Synergy_S5D5_ETB_Trace.zip
Streaming trace
The following sample project is designed to be used with J-Trace PRO and Ozone to demonstrate streaming trace. The project has been tested with the minimum requirements mentioned above and a Synergy TB-S5D5 eval board. The sample project comes with a pre-configured project file for Ozone that runs out-of-the box. In order to rebuild the sample project, SEGGER Embedded Studio can be used.
Renesas_Synergy_S5D5_Trace_Example.zip
