Difference between revisions of "Renesas EK-RA4M2"
(Created page with " __TOC__ This article describes specifics for the Renesas EK-RA4M2 evaluation board.<br> 450px == Preparing for J-Link == *C...") |
(→SETUP) |
||
| (One intermediate revision by the same user not shown) | |||
| Line 7: | Line 7: | ||
== Preparing for J-Link == |
== Preparing for J-Link == |
||
| − | *Connect the J-Link to |
+ | *Connect the J-Link to this pins: |
| + | {| class="seggertable" |
||
| − | *Power the board via J10. |
||
| + | |- |
||
| + | ! J-Link Pin || Connector !! Pin || Name |
||
| + | |- |
||
| + | | VTref || J4 || 1 || +3V3 |
||
| + | |- |
||
| + | | GND || J4 || 27 || GND |
||
| + | |- |
||
| + | | TMS/SWDIO || J3 || 3 || P108 |
||
| + | |- |
||
| + | | TCK/SWCLK || J4 || 26 || P300 |
||
| + | |} |
||
| + | *Power the board via J11. |
||
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
||
[[File:Renesas_R7FA6M3AH_EK-RA4M2_connect.png|400px]] |
[[File:Renesas_R7FA6M3AH_EK-RA4M2_connect.png|400px]] |
||
| + | |||
== Example Project== |
== Example Project== |
||
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the Renesas EK-RA4M2.<br>It is a simple Hello World sample linked into the internal flash.<br> |
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the Renesas EK-RA4M2.<br>It is a simple Hello World sample linked into the internal flash.<br> |
||
| Line 16: | Line 29: | ||
*J-Link software: V8.10b |
*J-Link software: V8.10b |
||
*Hardware: Renesas EK-RA4M2 |
*Hardware: Renesas EK-RA4M2 |
||
| − | *Link: [[File: |
+ | *Link: [[File:Renesas_R7FA4M2AD_TestProject_ES_V810b.zip]] |
Latest revision as of 15:59, 28 June 2024
This article describes specifics for the Renesas EK-RA4M2 evaluation board.
Preparing for J-Link
- Connect the J-Link to this pins:
| J-Link Pin | Connector | Pin | Name |
|---|---|---|---|
| VTref | J4 | 1 | +3V3 |
| GND | J4 | 27 | GND |
| TMS/SWDIO | J3 | 3 | P108 |
| TCK/SWCLK | J4 | 26 | P300 |
- Power the board via J11.
- Verify the Connection with e.g. J-Link Commander. The output should look as follows:
Example Project
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the Renesas EK-RA4M2.
It is a simple Hello World sample linked into the internal flash.
SETUP
- J-Link software: V8.10b
- Hardware: Renesas EK-RA4M2
- Link: File:Renesas R7FA4M2AD TestProject ES V810b.zip
