Difference between revisions of "NXP NxH2004 SDK"
(→Sample projects) |
|||
Line 1: | Line 1: | ||
+ | __TOC__ |
||
− | [[File: NXP_NxH2004_SDK.jpg | thumb | right | 500 px | NxH2004SDK evaluation board]] |
||
The NXP NxH2004 SDK board is a small evaluation board with a [[NXP NxH2004]] MCU. |
The NXP NxH2004 SDK board is a small evaluation board with a [[NXP NxH2004]] MCU. |
||
It can be used by mounting it to the NxH2004-3675 SDK motherboard. |
It can be used by mounting it to the NxH2004-3675 SDK motherboard. |
||
+ | [[File: NXP_NxH2004_SDK.jpg | 450 px]] |
||
− | __TOC__ |
||
+ | |||
+ | == Minimum requirements == |
||
+ | * J-Link software V7.22 or later |
||
+ | |||
+ | == Preparing for J-Link == |
||
+ | * Make sure that you install the correct board on the NxH2004-3675 board. |
||
+ | * Connect the J-Link to the SWD header (J33 (SWD)) |
||
+ | * Make sure that all jumpers and switches are set as in the picture above. |
||
+ | * Power the board via external USB power supply (J24) |
||
+ | * Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows:<br> |
||
+ | [[File:NXP_NxH2004_Connect.PNG|400px]] |
||
− | == |
+ | == Example Project== |
+ | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the NXP NxH2004 SDK. |
||
− | * "Hello World" RTT Sample (Embedded Studio V5.42a): [[File:NXP_NxH2004SDK_RTT_Sample.zip]] |
||
+ | It is a simple [[RTT]] Hello World sample linked into the internal flash. |
||
+ | === Setup === |
||
+ | *J-Link software: V7.22 |
||
+ | *Embedded Studio: V5.42a |
||
+ | *Hardware: NXP NxH2004-3675 SDK with NXP NxH2004 board |
||
+ | *Link: [[File:NXP_NxH2004SDK_RTT_Sample.zip]] |
Revision as of 15:23, 21 May 2021
The NXP NxH2004 SDK board is a small evaluation board with a NXP NxH2004 MCU. It can be used by mounting it to the NxH2004-3675 SDK motherboard.
Minimum requirements
- J-Link software V7.22 or later
Preparing for J-Link
- Make sure that you install the correct board on the NxH2004-3675 board.
- Connect the J-Link to the SWD header (J33 (SWD))
- Make sure that all jumpers and switches are set as in the picture above.
- Power the board via external USB power supply (J24)
- Verify the Connection with e.g. J-Link Commander. The output should look as follows:
Example Project
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the NXP NxH2004 SDK. It is a simple RTT Hello World sample linked into the internal flash.
Setup
- J-Link software: V7.22
- Embedded Studio: V5.42a
- Hardware: NXP NxH2004-3675 SDK with NXP NxH2004 board
- Link: File:NXP NxH2004SDK RTT Sample.zip