Difference between revisions of "Electrosmith Daisy Seed"
m (Matthias moved page Daisy Seed to Electrosmith Daisy Seed) |
(→Example implementation) |
||
Line 9: | Line 9: | ||
== Example implementation == |
== Example implementation == |
||
− | As described in the generic article, the reference flash algorithm is based on the SEGGER ''Open Flashloader'' and therefore needs to be added manually using a JLinkDevices.xml file. An example JLinkDevices.xml file as well as pinout used on the Daisy Seed board, is given below. For further information regarding the ''Open Flashloader'' and how to use the JLinkDevices.xml file, please refer to the |
+ | As described in the generic article, the reference flash algorithm is based on the SEGGER ''Open Flashloader'' and therefore needs to be added manually using a JLinkDevices.xml file. An example JLinkDevices.xml file as well as pinout used on the Daisy Seed board, is given below. For further information regarding the ''Open Flashloader'' and how to use the JLinkDevices.xml file, please refer to the Open Flashloader article, section [[Open_Flashloader#Using_a_Precompiled_Flashloader | Using a precompiled Flashloader]]. |
===Quad-SPI Interface Pins=== |
===Quad-SPI Interface Pins=== |
||
Line 37: | Line 37: | ||
</Device> |
</Device> |
||
</Database> |
</Database> |
||
− | |||
− | For further information how to include this flashloader into your J-Link software, please refer to:<br> |
||
− | https://wiki.segger.com/Adding_Support_for_New_Devices#Using_a_Precompiled_Flashloader |
||
===Flash algorithm (*.elf)=== |
===Flash algorithm (*.elf)=== |
Revision as of 14:55, 15 October 2021
Contents
This article describes specifics for the Electrosmith Daisy Seed evaluation board. The board contains the ST STM32H750IBK6 chip and has an ISSI IS25LP064 64 MBit SPI flash.
QSPI Flash Programming Support
Before continuing with this article, please read the generic article about QSPI flash programming support on STM32H7 devices (STM32H7 (Q)SPI support).
Example implementation
As described in the generic article, the reference flash algorithm is based on the SEGGER Open Flashloader and therefore needs to be added manually using a JLinkDevices.xml file. An example JLinkDevices.xml file as well as pinout used on the Daisy Seed board, is given below. For further information regarding the Open Flashloader and how to use the JLinkDevices.xml file, please refer to the Open Flashloader article, section Using a precompiled Flashloader.
Quad-SPI Interface Pins
The Electrosmith Daisy Seed uses the following port pins to interface the (Q)SPI flash.
Alternate function | Port / Pin |
---|---|
QSPI_CLK | PF10 |
QSPI_CS | PG6 |
QSPI_BK1_D0 | PF8 |
QSPI_BK1_D1 | PF9 |
QSPI_BK1_D2 | PF7 |
QSPI_BK1_D3 | PF6 |
JLinkDevices.xml
<Database> <Device> <ChipInfo Vendor="ST" Name="STM32H750IB_DaisySeed" Core="JLINK_CORE_CORTEX_M7" WorkRAMAddr="0x24000000" WorkRAMSize="0x00080000"/> <FlashBankInfo Name="QSPI Flash" BaseAddr="0x90000000" MaxSize="0x04000000" Loader="Devices/ElectroSmith/DaisySeed_Flashloader.elf" LoaderType="FLASH_ALGO_TYPE_OPEN" /> </Device> </Database>
Flash algorithm (*.elf)
This file contains the program routines used by the J-Link DLL during flash programming for single SPI flash using the above described pins.