Difference between revisions of "Electrosmith Daisy Seed"
(→Example implementation) |
(→JLinkDevices.xml) |
||
Line 31: | Line 31: | ||
===JLinkDevices.xml=== |
===JLinkDevices.xml=== |
||
+ | * The following example creates a new device entry, that only supports flash programming for the QSPI flash. |
||
<Database> |
<Database> |
||
<Device> |
<Device> |
||
Line 36: | Line 37: | ||
<FlashBankInfo Name="QSPI Flash" BaseAddr="0x90000000" MaxSize="0x04000000" Loader="Devices/ElectroSmith/DaisySeed_Flashloader.elf" LoaderType="FLASH_ALGO_TYPE_OPEN" /> |
<FlashBankInfo Name="QSPI Flash" BaseAddr="0x90000000" MaxSize="0x04000000" Loader="Devices/ElectroSmith/DaisySeed_Flashloader.elf" LoaderType="FLASH_ALGO_TYPE_OPEN" /> |
||
</Device> |
</Device> |
||
+ | </Database> |
||
+ | |||
+ | * This example replaces the existing entry for the STM32H750IB QSPI flash bank with one that uses the Daisy Seed flashloader. All other flashbanks (Internal flash) are unaffected and can still be programmed as with STM32H750IB devices. |
||
+ | <Database> |
||
+ | <Device> |
||
+ | <ChipInfo Vendor="ST" Name="STM32H750IB" /> |
||
+ | <FlashBankInfo Name="External QSPI flash" BaseAddr="0x90000000" MaxSize="0x04000000" Loader="Devices/ElectroSmith/DaisySeed_Flashloader.elf" LoaderType="FLASH_ALGO_TYPE_OPEN" /> |
||
+ | </Device> |
||
</Database> |
</Database> |
||
Revision as of 14:47, 19 October 2021
Contents
This article describes specifics for the Electrosmith Daisy Seed evaluation board. The board contains the ST STM32H750IBK6 chip and has an ISSI IS25LP064 64 MBit SPI flash.
QSPI Flash Programming Support
Before continuing with this article, please read the generic article about QSPI flash programming support on STM32H7 devices (STM32H7 (Q)SPI support).
Example implementation
As described in the generic article, the reference flash algorithm is based on the SEGGER Open Flashloader and therefore needs to be added manually using a JLinkDevices.xml file. An example JLinkDevices.xml file as well as pinout used on the Daisy Seed board, is given below. For further information regarding the Open Flashloader and how to use the JLinkDevices.xml file, please refer to the Open Flashloader article, section Using a precompiled Flashloader.
Quad-SPI Interface Pins
The Electrosmith Daisy Seed uses the following port pins to interface the (Q)SPI flash.
Alternate function | Port / Pin |
---|---|
QSPI_CLK | PF10 |
QSPI_CS | PG6 |
QSPI_BK1_D0 | PF8 |
QSPI_BK1_D1 | PF9 |
QSPI_BK1_D2 | PF7 |
QSPI_BK1_D3 | PF6 |
JLinkDevices.xml
- The following example creates a new device entry, that only supports flash programming for the QSPI flash.
<Database> <Device> <ChipInfo Vendor="ST" Name="STM32H750IB_DaisySeed" Core="JLINK_CORE_CORTEX_M7" WorkRAMAddr="0x24000000" WorkRAMSize="0x00080000"/> <FlashBankInfo Name="QSPI Flash" BaseAddr="0x90000000" MaxSize="0x04000000" Loader="Devices/ElectroSmith/DaisySeed_Flashloader.elf" LoaderType="FLASH_ALGO_TYPE_OPEN" /> </Device> </Database>
- This example replaces the existing entry for the STM32H750IB QSPI flash bank with one that uses the Daisy Seed flashloader. All other flashbanks (Internal flash) are unaffected and can still be programmed as with STM32H750IB devices.
<Database> <Device> <ChipInfo Vendor="ST" Name="STM32H750IB" /> <FlashBankInfo Name="External QSPI flash" BaseAddr="0x90000000" MaxSize="0x04000000" Loader="Devices/ElectroSmith/DaisySeed_Flashloader.elf" LoaderType="FLASH_ALGO_TYPE_OPEN" /> </Device> </Database>
Flash algorithm (*.elf)
This file contains the program routines used by the J-Link DLL during flash programming for single SPI flash using the above described pins.