Difference between revisions of "NXP RD-RW616-BGA IPA-2A/1A"
(Created page with "__TOC__ This article describes specifics for the NXP RD-RW616-BGA_IPA-2A/1A evaluation board.<br> '''[PICTURE OF BOARD]''' 450px == Preparing f...") |
|||
(4 intermediate revisions by one other user not shown) | |||
Line 1: | Line 1: | ||
+ | [[Category:Evalboards]] |
||
__TOC__ |
__TOC__ |
||
This article describes specifics for the NXP RD-RW616-BGA_IPA-2A/1A evaluation board.<br> |
This article describes specifics for the NXP RD-RW616-BGA_IPA-2A/1A evaluation board.<br> |
||
+ | [[File:NXP_RD-RW612-BGA_RW612EV_board.jpg|450px]] |
||
− | '''[PICTURE OF BOARD]''' |
||
− | [[File:VENDOR_BOARDNAME.jpg|450px]] |
||
== Preparing for J-Link == |
== Preparing for J-Link == |
||
− | * |
+ | * Power the board via J1 |
+ | * Jumper JP1 must be set in order to use J-Link |
||
− | *Power the board via........ |
||
+ | '''For use of SWD:''' |
||
+ | ** HD12 1-2 has to be closed (RF_CNTL_2/CON[11]) |
||
+ | ** Connect JLINK to P2 (SWD) |
||
+ | '''For use of JTAG:''' |
||
+ | ** HD12 1-2 has to be open (RF_CNTL_2/CON[11]) |
||
+ | ** Connect JLINK to J19 (JTAG) |
||
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
||
+ | [[File:NXP_RD-RW612-BGA_RW612EV_connect.png|400px]] |
||
− | '''[PICTURE OF CONNECT]''' |
||
− | [[File:VENDOR_DEVICE_CONNECT.PNG|400px]] |
||
== Example Project== |
== Example Project== |
||
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the NXP RD-RW616-BGA_IPA-2A/1A.<br>It is a simple Hello World sample linked into the internal flash.<br> |
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the NXP RD-RW616-BGA_IPA-2A/1A.<br>It is a simple Hello World sample linked into the internal flash.<br> |
||
====SETUP==== |
====SETUP==== |
||
− | *J-Link software: |
+ | *J-Link software: V7.92c |
− | *Embedded Studio: |
+ | *Embedded Studio: V7.20 |
*Hardware: NXP RD-RW616-BGA_IPA-2A/1A |
*Hardware: NXP RD-RW616-BGA_IPA-2A/1A |
||
− | *Link: [[File: |
+ | *Link: [[File:NXP_RW61x_TestProject_ES_7V20.zip]] |
Latest revision as of 13:20, 15 May 2024
This article describes specifics for the NXP RD-RW616-BGA_IPA-2A/1A evaluation board.
Preparing for J-Link
- Power the board via J1
- Jumper JP1 must be set in order to use J-Link
For use of SWD:
- HD12 1-2 has to be closed (RF_CNTL_2/CON[11])
- Connect JLINK to P2 (SWD)
For use of JTAG:
- HD12 1-2 has to be open (RF_CNTL_2/CON[11])
- Connect JLINK to J19 (JTAG)
- Verify the Connection with e.g. J-Link Commander. The output should look as follows:
Example Project
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the NXP RD-RW616-BGA_IPA-2A/1A.
It is a simple Hello World sample linked into the internal flash.
SETUP
- J-Link software: V7.92c
- Embedded Studio: V7.20
- Hardware: NXP RD-RW616-BGA_IPA-2A/1A
- Link: File:NXP RW61x TestProject ES 7V20.zip