Difference between revisions of "STM32VLDISCOVERY"
(Created page with "__TOC__ This article describes specifics for the ST STM32VLDISCOVERY board.<br> 400px == Preparing for J-Link == *Power the board via (Min...") |
|||
(4 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
+ | [[Category:Evalboards]] |
||
__TOC__ |
__TOC__ |
||
Line 6: | Line 7: | ||
== Preparing for J-Link == |
== Preparing for J-Link == |
||
+ | * Connect the board with jumping wires to your J-Link (see table below)<br>For information about the J-Link pinout please refer to the following page: [https://www.segger.com/products/debug-probes/j-link/technology/interface-description/#swd-connector-pinout J-Link SWD pinout]. |
||
− | *Power the board via (Mini USB) |
||
+ | |||
+ | {| class="wikitable" |
||
+ | |- |
||
+ | ! J-Link 20 pin debug interface !! Pin on evaluation board |
||
+ | |- |
||
+ | | Pin 1 (VTref, yellow) || at 3V3 pin header |
||
+ | |- |
||
+ | | Pin 4 (GND, black) || at GND pin header |
||
+ | |- |
||
+ | | Pin 7 (SWDIO, green) || at PA13 pin header |
||
+ | |- |
||
+ | | Pin 9 (SWCLK, yellow) || at PA14 pin header |
||
+ | |- |
||
+ | | Pin 13 (SWO, black) || at PB3 pin header |
||
+ | |- |
||
+ | | Pin 15 (RESET, blue) || at RST pin header |
||
+ | |- |
||
+ | | Pin 19 (5V-Supply, Red)|| at 5V pin header |
||
+ | |} |
||
+ | The result should be looking like this: |
||
+ | |||
+ | [[File:STM32VLDISCOVERY_wired.jpg | 300px | ST STM32VLDISCOVERY wired with jumper cables]] |
||
+ | [[File:STM32VLDISCOVERY_wired2.jpg | 300px | ST STM32VLDISCOVERY wired with jumper cables]] |
||
+ | |||
+ | *Power the board via (Mini USB or 5V Pin) |
||
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
||
[[File:STM32VLDISCOVERY_con.PNG|400px]] |
[[File:STM32VLDISCOVERY_con.PNG|400px]] |
Latest revision as of 11:32, 15 May 2024
This article describes specifics for the ST STM32VLDISCOVERY board.
Preparing for J-Link
- Connect the board with jumping wires to your J-Link (see table below)
For information about the J-Link pinout please refer to the following page: J-Link SWD pinout.
J-Link 20 pin debug interface | Pin on evaluation board |
---|---|
Pin 1 (VTref, yellow) | at 3V3 pin header |
Pin 4 (GND, black) | at GND pin header |
Pin 7 (SWDIO, green) | at PA13 pin header |
Pin 9 (SWCLK, yellow) | at PA14 pin header |
Pin 13 (SWO, black) | at PB3 pin header |
Pin 15 (RESET, blue) | at RST pin header |
Pin 19 (5V-Supply, Red) | at 5V pin header |
The result should be looking like this:
- Power the board via (Mini USB or 5V Pin)
- Verify the Connection with e.g. J-Link Commander. The output should look as follows:
- Note select device: "".
Example Project
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the ST STM32VLDISCOVERY.
It is a simple Hello World sample linked into the internal flash.
SETUP
- J-Link software: V7.90
- Embedded Studio: V7.20
- Hardware: ST NUCLEO-F103RB
- Link: File:STM32VLDISCOVERY.zip