Difference between revisions of "GigaDevice GD32350C-START"
(Created page with "__TOC__ This article describes specifics for the GigaDevice GD32350C-START evaluation board.<br> 450px == Preparing fo...") |
|||
Line 2: | Line 2: | ||
This article describes specifics for the GigaDevice GD32350C-START evaluation board.<br> |
This article describes specifics for the GigaDevice GD32350C-START evaluation board.<br> |
||
− | [[File:GigaDevice_GD32350C- |
+ | [[File:GigaDevice_GD32350C-START_GD32F350C8_board.jpg|450px]] |
== Preparing for J-Link == |
== Preparing for J-Link == |
||
Line 10: | Line 10: | ||
! J-Link Pin || Connector !! Pin || Name |
! J-Link Pin || Connector !! Pin || Name |
||
|- |
|- |
||
− | | VTref || |
+ | | VTref || JP2 || 19 || +3V3 |
|- |
|- |
||
− | | GND || |
+ | | GND || JP2 || 20 || GND |
|- |
|- |
||
− | | TMS/SWDIO || |
+ | | TMS/SWDIO || JP2 || 4 || PA13 |
|- |
|- |
||
− | | TCK/SWCLK || |
+ | | TCK/SWCLK || JP2 || 7 || PA14 |
|} |
|} |
||
− | *Power the board via |
+ | *Power the board via CN1. |
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
||
[[File:GigaDevice_GD32350C-START_GD32350C8_connect.png|400px]] |
[[File:GigaDevice_GD32350C-START_GD32350C8_connect.png|400px]] |
||
Line 27: | Line 27: | ||
*Embedded Studio: V7.12a |
*Embedded Studio: V7.12a |
||
*Hardware: GigaDevice GD32350C-START |
*Hardware: GigaDevice GD32350C-START |
||
− | *Link: [[File: |
+ | *Link: [[File:GigaDevice_GD32F350C8_TestProject_ES_V810b.zip]] |
Revision as of 13:31, 3 April 2024
This article describes specifics for the GigaDevice GD32350C-START evaluation board.
Preparing for J-Link
- Connect the J-Link to this pins:
J-Link Pin | Connector | Pin | Name |
---|---|---|---|
VTref | JP2 | 19 | +3V3 |
GND | JP2 | 20 | GND |
TMS/SWDIO | JP2 | 4 | PA13 |
TCK/SWCLK | JP2 | 7 | PA14 |
- Power the board via CN1.
- Verify the Connection with e.g. J-Link Commander. The output should look as follows:
Example Project
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the GigaDevice GD32350C-START.
It is a simple Hello World sample linked into the internal flash.
SETUP
- Embedded Studio: V7.12a
- Hardware: GigaDevice GD32350C-START
- Link: File:GigaDevice GD32F350C8 TestProject ES V810b.zip