Difference between revisions of "ArteryTek AT-START-F402"
(Created page with "__TOC__ This article describes specifics for the Artery AT-START-F405 evaluation board.<br> 450px == Preparing for J-Li...") |
|||
Line 1: | Line 1: | ||
__TOC__ |
__TOC__ |
||
− | This article describes specifics for the Artery AT-START- |
+ | This article describes specifics for the Artery AT-START-F402 evaluation board.<br> |
− | [[File:Artery_AT-START- |
+ | [[File:Artery_AT-START-F402_AT32F402RCT7-7_board.jpg|450px]] |
== Preparing for J-Link == |
== Preparing for J-Link == |
||
Line 25: | Line 25: | ||
*Power the board via USB CN6 or CN4. |
*Power the board via USB CN6 or CN4. |
||
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
||
− | [[File:Artery_AT-START- |
+ | [[File:Artery_AT-START-F402_AT32F402RCT7-7_connect.png|400px]] |
== Example Project== |
== Example Project== |
||
− | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the Artery AT-START- |
+ | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the Artery AT-START-F402.<br> |
It is a simple Hello World sample linked into the internal flash.<br> |
It is a simple Hello World sample linked into the internal flash.<br> |
||
====SETUP==== |
====SETUP==== |
||
− | *J-Link software: V7. |
+ | *J-Link software: V7.94h |
*Embedded Studio: V7.20 |
*Embedded Studio: V7.20 |
||
− | *Hardware: Artery AT-START- |
+ | *Hardware: Artery AT-START-F402 |
− | *Link: [[File:Artery_AT-START- |
+ | *Link: [[File:Artery_AT-START-F402_AT32F402RCT7-7_TestProject_ES_7V20.zip]] |
Revision as of 14:14, 25 January 2024
This article describes specifics for the Artery AT-START-F402 evaluation board.
Preparing for J-Link
- Connect the J-Link to this pins:
J-Link Pin | Connector | Pin | Name |
---|---|---|---|
VTref | J1 | 32 | VDD |
GND | J1 | 31 | GND |
TDI | J1 | 18 | PA15 |
TMS/SWDIO | J1 | 14 | PA13/SWDIO |
TCK/SWCLK | J1 | 17 | PA14/SWCLK |
TDO/SWO | J1 | 23 | PB3 |
RESET | J2 | 7 | NRST |
- Power the board via USB CN6 or CN4.
- Verify the Connection with e.g. J-Link Commander. The output should look as follows:
Example Project
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the Artery AT-START-F402.
It is a simple Hello World sample linked into the internal flash.
SETUP
- J-Link software: V7.94h
- Embedded Studio: V7.20
- Hardware: Artery AT-START-F402
- Link: File:Artery AT-START-F402 AT32F402RCT7-7 TestProject ES 7V20.zip