Difference between revisions of "ArteryTek AT-START-F407"
(Created page with "__TOC__ This article describes specifics for the Artery AT-START-F407 evaluation board.<br> 450px == Preparing for J-Lin...") |
m (Torben.scharping moved page Artery AT-START-F407 to ArteryTek AT-START-F407) |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
__TOC__ |
__TOC__ |
||
| − | This article describes specifics for the |
+ | This article describes specifics for the ArteryTek AT-START-F407 evaluation board.<br> |
[[File:Artery_AT-START-F407_AT32F407VGT7_board.jpg|450px]] |
[[File:Artery_AT-START-F407_AT32F407VGT7_board.jpg|450px]] |
||
| Line 26: | Line 26: | ||
*Power the board via CN4. |
*Power the board via CN4. |
||
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
||
| − | [[File:Artery_AT |
+ | [[File:Artery_AT-START-F407_AT32F407VGT7_connect.png|400px]] |
== Example Project== |
== Example Project== |
||
| − | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the |
+ | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the ArteryTek AT-START-F407.<br> |
It is a simple Hello World sample linked into the internal flash.<br> |
It is a simple Hello World sample linked into the internal flash.<br> |
||
====SETUP==== |
====SETUP==== |
||
*J-Link software: V7.94j |
*J-Link software: V7.94j |
||
*Embedded Studio: V7.20 |
*Embedded Studio: V7.20 |
||
| − | *Hardware: |
+ | *Hardware: ArteryTek AT-START-F407 |
| − | *Link: [[File:Artery_AT |
+ | *Link: [[File:Artery_AT-START-F407_AT32F407VGT7_TestProject_ES_7V20.zip]] |
Latest revision as of 16:33, 8 February 2024
This article describes specifics for the ArteryTek AT-START-F407 evaluation board.
Preparing for J-Link
- Connect the J-Link to this pins:
| J-Link Pin | Connector | Pin | Name |
|---|---|---|---|
| VTref | J1 | 23 | VDD |
| GND | J1 | 22 | GND |
| TDI | J1 | 25 | PA15 |
| TMS/SWDIO | J1 | 20 | PA13 |
| TCK/SWCLK | J1 | 24 | PA14 |
| TDO/SWO | J1 | 37 | PB3 |
| RESET | J2 | 14 | NRST |
- Power the board via CN4.
- Verify the Connection with e.g. J-Link Commander. The output should look as follows:
Example Project
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the ArteryTek AT-START-F407.
It is a simple Hello World sample linked into the internal flash.
SETUP
- J-Link software: V7.94j
- Embedded Studio: V7.20
- Hardware: ArteryTek AT-START-F407
- Link: File:Artery AT-START-F407 AT32F407VGT7 TestProject ES 7V20.zip
