Difference between revisions of "How to use SWO with GDB"
Line 1: | Line 1: | ||
− | GDB does not |
+ | Generally a GDB client does not support SWO. But luckily, the J-Link GDB server is able to work around this and send SWO data to a socket. |
− | This article is a step-by-step guide about how to use SWO with GDB. |
+ | This article is a step-by-step guide about how to use SWO with J-Linkg and a GDB client. |
__TOC__ |
__TOC__ |
||
Line 9: | Line 9: | ||
=Example with a MK22FN512xxx12 device using putty (default ports)= |
=Example with a MK22FN512xxx12 device using putty (default ports)= |
||
− | This example shows how to setup GDB for SWO. |
+ | This example shows how to setup J-Link GDB Server, a GDB client and Putty for SWO. |
It was created by using default port settings. |
It was created by using default port settings. |
||
Further information about setting different ports and more can be found in UM08001. |
Further information about setting different ports and more can be found in UM08001. |
||
In this example the following applications were used: |
In this example the following applications were used: |
||
− | *J-Llink GDB Server |
+ | *J-Llink GDB Server V6.54a |
− | *ARM GDB |
+ | *ARM GDB client (V7.3.1) |
− | *Putty |
+ | *Putty (V0.70) |
==Setting up the J-Link GDB Server== |
==Setting up the J-Link GDB Server== |
||
# Open the J-Link GDB Server |
# Open the J-Link GDB Server |
||
# Set all options as required:<br>[[File: SetupSWO_GDBServer.PNG]] |
# Set all options as required:<br>[[File: SetupSWO_GDBServer.PNG]] |
||
− | # Start the GDB |
+ | # Start the J-Link GDB Server |
==Setting up the GDB client== |
==Setting up the GDB client== |
||
# Open a command line GDB client |
# Open a command line GDB client |
||
− | # Connect to the GDB Server. This can be achieved via these commands: |
+ | # Connect to the J-Link GDB Server. This can be achieved via these commands: |
target remote :2331 |
target remote :2331 |
||
monitor SWO EnableTarget 0 0 1 0 |
monitor SWO EnableTarget 0 0 1 0 |
Revision as of 17:26, 21 November 2019
Generally a GDB client does not support SWO. But luckily, the J-Link GDB server is able to work around this and send SWO data to a socket. This article is a step-by-step guide about how to use SWO with J-Linkg and a GDB client.
Contents
Default settings
If not set differently, J-Link GDB Server will use default settings:
- Telnet port: 2331
- SWO data port: 2332
Example with a MK22FN512xxx12 device using putty (default ports)
This example shows how to setup J-Link GDB Server, a GDB client and Putty for SWO. It was created by using default port settings. Further information about setting different ports and more can be found in UM08001. In this example the following applications were used:
- J-Llink GDB Server V6.54a
- ARM GDB client (V7.3.1)
- Putty (V0.70)
Setting up the J-Link GDB Server
Setting up the GDB client
- Open a command line GDB client
- Connect to the J-Link GDB Server. This can be achieved via these commands:
target remote :2331 monitor SWO EnableTarget 0 0 1 0 c