J-Link Installer

From SEGGER Wiki
Revision as of 11:22, 30 November 2023 by Fabian (talk | contribs) (Available command line options)
Jump to: navigation, search
J-Link Installer options page

The J-Link Installer is an NSIS installer which installs the J-Link Software and Documentation Pack. The J-Link Installer can be installed for "all users" and since Version 6.49a also for "user". The latter does not require admin elevation.

Installation options

This section of the article describes the options that can be set prior to the installation.
Note: This is only valid for version 7.94 and on-wards.

Create entry in start menu

When checked, a start menu entry of the J-Link Software and Documentation Pack is created. Is selected by default.

Add shortcuts to desktop

When checked, a desktop shortcuts for J-Link Commander and J-Flash is created. Is selected by default.

Update DLL in other applications

When checked, the J-Link DLL Updater is started after installation. Requires admin rights. Starts the DLL Updater after installation. Is selected by default. Cannot be set when Install for this user only is selected.

Update existing installation OR Install a new instance

This option sets whether a J-Link Software and Documentation Pack installed prior to the same destination folder is to be uninstalled before the installation or not. By default, "Update existing installation" is selected. Uninstalls the J-Link version found in the Install directory.

Install for all users OR Install for this user only

This option sets whether the J-Link Software and Documentation Pack is installed for all users or for this user only. By default, "Install for all users" is selected.

Destination Folder

This is the folder the J-Link Software and Documentation Pack is to be installed to. It cannot be set when Install for this user only is selected. It can only be chosen whether the folder ends with _<Version> or not, by switching between Update existing and Install a new instance.
For defaults, refer to Command line options notes, (**).

Command line parameters

The J-Link Installer supports command line usage since version 6.49a. All options selectable in the GUI version of the installer can also be set by command line.

Available command line options

Command line Meaning Default Syntax
-InstAllUsers Install for all users 1[1] -InstAllUsers=<1/0>
-CreateStartMenuEntry Create a start menu entry 1 -CreateStartMenuEntry=<1/0>
-CreateDesktopShortCut Create a desktop shortcut 1 -CreateDesktopShortCut=<1/0>
-UpdateExisting Will uninstall the existing J-Link version in install directory prior to installation 0 -UpdateExisting=<1/0>
-Silent Start installer silent. Note: DLL updater wont be called if set to 1 0 -Silent=<1/0>
The following command lines are ignored, if "-InstAllUsers=0" is set
-InstUSBDriver (depr.) Install USB drivers[1][2] 0 -InstUSBDriver=<1/0>
-StartDLLUpdater Start DLL Updater after installation[1] 1 -StartDLLUpdater=<1/0>
-InstDir Set the install directory[1] X[3] -InstDir="<Path>"
  1. 1.0 1.1 1.2 1.3 Requires admin rights.
  2. Deprecated legacy option. Should not be used.
  3. There are 6 defaults for the install path, depending on the installer and the installer options:
    Presets 32-bit installer 64-bit installer
    -InstAllUsers=1 -UpdateExisting=1 %ProgramFiles(x86)%\SEGGER\JLink %ProgramFiles%\SEGGER\JLink
    -InstAllUsers=1 -UpdateExisting=0 %ProgramFiles(x86)%\SEGGER\JLink_<Version> %ProgramFiles%\SEGGER\JLink_<Version>
    -InstAllUsers=0 -UpdateExisting=1 %UserProfile%\SEGGER\JLink %UserProfile%\SEGGER\JLink
    -InstAllUsers=0 -UpdateExisting=0 %UserProfile%\SEGGER\JLink_<Version> %UserProfile%\SEGGER\JLink_<Version>