Difference between revisions of "Mindmotion BIRD-F3F5 MM32F5287"
m (Torben.scharping moved page Mindmotion BIRD F3 F5 MM32F5287 to Mindmotion BIRD-F3F5 MM32F5287) |
|||
Line 3: | Line 3: | ||
This article describes specifics for the Mindmotion PLUS5270 MM32F5270 evaluation board. |
This article describes specifics for the Mindmotion PLUS5270 MM32F5270 evaluation board. |
||
− | [[File: |
+ | [[File:MindMotion_BIRD-F3F5_MM32F5287_Board.jpg|450px]] |
== Minimum requirements == |
== Minimum requirements == |
||
− | * J-Link software V7. |
+ | * J-Link software V7.86i or later |
== Preparing for J-Link == |
== Preparing for J-Link == |
||
− | *Connect the J-Link to the SWD header ( |
+ | *Connect the J-Link to the SWD header (J1) |
− | *Power the board via |
+ | *Power the board via USB-C (J5) |
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
||
− | [[File: |
+ | [[File:MindMotion_BIRD-F3F5_MM32F5287_Connect.png|400px]] |
== Example Project== |
== Example Project== |
||
− | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the |
+ | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the MindMotion BIRD-F3/F5 MM32F5287. <br> |
It is a simple Hello World sample linked into the internal flash.<br> |
It is a simple Hello World sample linked into the internal flash.<br> |
||
====SETUP==== |
====SETUP==== |
||
− | *J-Link software: V7. |
+ | *J-Link software: V7.86i |
*Embedded Studio: V6.34 |
*Embedded Studio: V6.34 |
||
− | *Hardware: |
+ | *Hardware: MindMotion BIRD-F3/F5 MM32F5287 |
*Link: [[File:MM_PLUS5270_MM32F5270_TestProject_ES_V634.zip]] |
*Link: [[File:MM_PLUS5270_MM32F5270_TestProject_ES_V634.zip]] |
Revision as of 17:09, 18 April 2023
This article describes specifics for the Mindmotion PLUS5270 MM32F5270 evaluation board.
Minimum requirements
- J-Link software V7.86i or later
Preparing for J-Link
- Connect the J-Link to the SWD header (J1)
- Power the board via USB-C (J5)
- Verify the Connection with e.g. J-Link Commander. The output should look as follows:
Example Project
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the MindMotion BIRD-F3/F5 MM32F5287.
It is a simple Hello World sample linked into the internal flash.
SETUP
- J-Link software: V7.86i
- Embedded Studio: V6.34
- Hardware: MindMotion BIRD-F3/F5 MM32F5287
- Link: File:MM PLUS5270 MM32F5270 TestProject ES V634.zip