Difference between revisions of "TI LaunchPad CC1354P10"
(Created page with "__TOC__ This article describes specifics for the TI LaunchPad CC1354P10 evaluation board.<br> '''[PICTURE OF BOARD]''' 450px == Preparing for J...") |
|||
(5 intermediate revisions by one other user not shown) | |||
Line 1: | Line 1: | ||
+ | [[Category:Evalboards]] |
||
__TOC__ |
__TOC__ |
||
This article describes specifics for the TI LaunchPad CC1354P10 evaluation board.<br> |
This article describes specifics for the TI LaunchPad CC1354P10 evaluation board.<br> |
||
+ | [[File:TI_LaunchPadCC1354P10.jpg|450px]] |
||
− | '''[PICTURE OF BOARD]''' |
||
− | [[File:VENDOR_BOARDNAME.jpg|450px]] |
||
− | |||
== Preparing for J-Link == |
== Preparing for J-Link == |
||
+ | *Make sure that the RST, TMS, TCK, TDD, TDI and SWO jumper are "disabled" (marked as number 1 in the screenshot above) |
||
− | *Connect the J-Link to ...... |
||
+ | *Connect the J-Link to Target In (9-Pin Cortex-M connector; marked as number 2 in the screenshot above) |
||
− | *Power the board via........ |
||
+ | *Power the board via micro USB |
||
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
||
+ | [[File:TI_CC1354P10_Connect.PNG|400px]] |
||
− | '''[PICTURE OF CONNECT]''' |
||
− | [[File:VENDOR_DEVICE_CONNECT.PNG|400px]] |
||
== Example Project== |
== Example Project== |
||
− | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the |
+ | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the TI LaunchPad CC1354P10.<br>It is a simple Hello World sample linked into the internal flash.<br> |
====SETUP==== |
====SETUP==== |
||
− | *J-Link software: |
+ | *J-Link software: V7.86 |
− | *Embedded Studio: |
+ | *Embedded Studio: V6.34 |
− | *Hardware: |
+ | *Hardware: TI LaunchPad CC1354P10 |
− | *Link: [[File: |
+ | *Link: [[File:TI_CC1354P10_TestProject_ES_V634.zip]] |
Latest revision as of 15:12, 8 May 2024
This article describes specifics for the TI LaunchPad CC1354P10 evaluation board.
Preparing for J-Link
- Make sure that the RST, TMS, TCK, TDD, TDI and SWO jumper are "disabled" (marked as number 1 in the screenshot above)
- Connect the J-Link to Target In (9-Pin Cortex-M connector; marked as number 2 in the screenshot above)
- Power the board via micro USB
- Verify the Connection with e.g. J-Link Commander. The output should look as follows:
Example Project
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the TI LaunchPad CC1354P10.
It is a simple Hello World sample linked into the internal flash.
SETUP
- J-Link software: V7.86
- Embedded Studio: V6.34
- Hardware: TI LaunchPad CC1354P10
- Link: File:TI CC1354P10 TestProject ES V634.zip