Difference between revisions of "Zedboard Evalboard"
(Created page with "The Xilinx ZedBoard is a complete development kit for the Xilinx Zynq7000 SoC. Xilinx Zynq7000 is a high end SoC with 2x Cortex-A9 cores and programmable FPGA logic on-chip.") |
(→Board connection) |
||
(7 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
+ | |||
− | The Xilinx ZedBoard is a complete development kit for the Xilinx Zynq7000 SoC. Xilinx Zynq7000 is a high end SoC with 2x Cortex-A9 cores and programmable FPGA logic on-chip. |
||
+ | |||
+ | __TOC__ |
||
+ | |||
+ | The Xilinx ZedBoard is a complete development kit for the Xilinx Zynq7000 SoC. The Xilinx Zynq7000 is a high-end SoC which incorporates a dual core Cortex-A9 (2x Cortex-A9) and programmable FPGA logic on-chip. |
||
+ | |||
+ | = J-Link support = |
||
+ | J-Link supports the Xilinx Zynq7000 series devices. [https://www.segger.com/downloads/jlink/#J-LinkSoftwareAndDocumentationPack Download latest release] |
||
+ | |||
+ | == J-Link device selection in J-Link Commander == |
||
+ | Please note that for the device selection in J-Link Commander, quotes are needed around the device name (as shown in the screenshot below). This is due to the nature of the Zynq7000 device names, containing spaces. Apart from that, there is nothing special to be taken care of. |
||
+ | |||
+ | '''Note:''' The device selection is mandatory to make sure that J-Link applies the correct connect and reset sequences to the Zynq 7000 series devices. By selecting "generic Cortex-A9" correct functionality cannot be guaranteed. |
||
+ | [[File:Xilinx_Zynq7020_ZedBoard_Commander.png|Xilinx ZedBoard|thumb|none]] |
||
+ | |||
+ | = Board connection = |
||
+ | The ZedBoard provides a Xilinx specific 14-pin debug connector. In order to connect J-Link to this board, the [https://www.segger.com/products/debug-probes/j-link/accessories/adapters/xilinx-adapter/ J-Link Xilinx adapter] is needed. |
||
+ | |||
+ | [[File:Xilinx_ZedBoard_JTAGConnector.png|Debug header|thumb|none]] |
||
+ | [[File:Xilinx_ZedBoard.png|Xilinx ZedBoard|thumb|none]] |
||
+ | |||
+ | <references/> |
Latest revision as of 11:46, 1 October 2018
The Xilinx ZedBoard is a complete development kit for the Xilinx Zynq7000 SoC. The Xilinx Zynq7000 is a high-end SoC which incorporates a dual core Cortex-A9 (2x Cortex-A9) and programmable FPGA logic on-chip.
J-Link support
J-Link supports the Xilinx Zynq7000 series devices. Download latest release
J-Link device selection in J-Link Commander
Please note that for the device selection in J-Link Commander, quotes are needed around the device name (as shown in the screenshot below). This is due to the nature of the Zynq7000 device names, containing spaces. Apart from that, there is nothing special to be taken care of.
Note: The device selection is mandatory to make sure that J-Link applies the correct connect and reset sequences to the Zynq 7000 series devices. By selecting "generic Cortex-A9" correct functionality cannot be guaranteed.
Board connection
The ZedBoard provides a Xilinx specific 14-pin debug connector. In order to connect J-Link to this board, the J-Link Xilinx adapter is needed.