Difference between revisions of "Silicon Labs BRD4271A"
(Created page with "__TOC__ This article describes specifics for the Silicon Labs BRD4271A evaluation board.<br> '''[PICTURE OF BOARD]''' 450px == Preparing for J-...") |
|||
(6 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
__TOC__ |
__TOC__ |
||
− | This article describes specifics for the Silicon Labs BRD4271A evaluation board.<br> |
+ | This article describes specifics for the Silicon Labs BRD4271A (EFR32xG25) extension board installed on the PCB4001 carrier board evaluation board.<br> |
+ | [[File:SiLabs_EFR32FG25B1920_board.jpg|450px]] |
||
− | '''[PICTURE OF BOARD]''' |
||
− | [[File:VENDOR_BOARDNAME.jpg|450px]] |
||
== Preparing for J-Link == |
== Preparing for J-Link == |
||
− | *Connect the J-Link to |
+ | *Connect the J-Link to the 20-pin debug connector. |
− | *Power the board |
+ | *Power the board using the mini USB connector. |
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
* Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
||
+ | [[File:SiLabs_EFR32FG25B1920_copnnect.png|400px]] |
||
− | '''[PICTURE OF CONNECT]''' |
||
− | [[File:VENDOR_DEVICE_CONNECT.PNG|400px]] |
||
== Example Project== |
== Example Project== |
||
− | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the |
+ | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the Silicon Labs BRD4210A.<br>It is a simple Hello World sample linked into the internal flash.<br> |
====SETUP==== |
====SETUP==== |
||
− | *J-Link software: |
+ | *J-Link software: V7.88h |
− | *Embedded Studio: |
+ | *Embedded Studio: V6.34 |
+ | *Hardware: Silicon Labs BRD4210A extension board installed on the PCB4001 carrier board |
||
− | *Hardware: [SiliconVendor] [EvalBoardName] |
||
− | *Link: [[File: |
+ | *Link: [[File:SiliconLabs_EFR32FG25BxxxF1920_TestProject_ES_V634.zip]] |
Revision as of 13:47, 14 June 2023
This article describes specifics for the Silicon Labs BRD4271A (EFR32xG25) extension board installed on the PCB4001 carrier board evaluation board.
Preparing for J-Link
- Connect the J-Link to the 20-pin debug connector.
- Power the board using the mini USB connector.
- Verify the Connection with e.g. J-Link Commander. The output should look as follows:
Example Project
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the Silicon Labs BRD4210A.
It is a simple Hello World sample linked into the internal flash.
SETUP
- J-Link software: V7.88h
- Embedded Studio: V6.34
- Hardware: Silicon Labs BRD4210A extension board installed on the PCB4001 carrier board
- Link: File:SiliconLabs EFR32FG25BxxxF1920 TestProject ES V634.zip