Difference between revisions of "Telink TLSR9518ADK80D"
(Created page with " thumb | right | 500 px | Telink TLSR9518ADK80D evaluation board (TLSR9518 series) The Telink TLSR9518ADK80D is a Telink_TLSR9518|Telink...") |
|||
(2 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
− | [[File: Telink_TLSR9518ADK80D.png | thumb | right | |
+ | [[File: Telink_TLSR9518ADK80D.png | thumb | right | 300 px | Telink TLSR9518ADK80D evaluation board (TLSR9518 series)]] |
The Telink TLSR9518ADK80D is a [[Telink_TLSR9518|Telink TLSR9518]] evaluation board. |
The Telink TLSR9518ADK80D is a [[Telink_TLSR9518|Telink TLSR9518]] evaluation board. |
||
Line 11: | Line 11: | ||
For further information please refer to the [http://wiki.telink-semi.cn/wiki/chip-series/TLSR9-Series/ Telink TLSR9 wiki page] |
For further information please refer to the [http://wiki.telink-semi.cn/wiki/chip-series/TLSR9-Series/ Telink TLSR9 wiki page] |
||
+ | |||
+ | |||
+ | |||
== Setting up with J-Link == |
== Setting up with J-Link == |
||
− | [[File: |
+ | [[File: Telink_TLSR9518ADK80D_DebugFront.png | thumb | right | 250 px | Telink TLSR9518 series debug interface connection front]] |
+ | [[File: Telink_TLSR9518ADK80D_DebugRear.png | thumb | right | 250 px | Telink TLSR9518 series debug interface connection rear]] |
||
The Telink TLSR9518ADK80D evaluation board comes with an external JTAG debug connector (6 pins: TDI, TDO, TCK, TMS, GND, VBUS). |
The Telink TLSR9518ADK80D evaluation board comes with an external JTAG debug connector (6 pins: TDI, TDO, TCK, TMS, GND, VBUS). |
||
To set the board up with J-Link, the following steps are required: |
To set the board up with J-Link, the following steps are required: |
||
Line 32: | Line 36: | ||
| "DEBUG" "GND" || 4 || GND |
| "DEBUG" "GND" || 4 || GND |
||
|- |
|- |
||
− | | "VBUS" || 1 || VTref |
+ | | "VBUS" || 1 || VTref |
|} |
|} |
||
</li> |
</li> |
||
</ol> |
</ol> |
||
'''Note:''' For a more reliable, simpler solution, the [https://www.segger.com/products/debug-probes/j-link/accessories/adapters/segger-flying-wire-adapter/ SEGGER Flying Wire Adapter] is recommended. |
'''Note:''' For a more reliable, simpler solution, the [https://www.segger.com/products/debug-probes/j-link/accessories/adapters/segger-flying-wire-adapter/ SEGGER Flying Wire Adapter] is recommended. |
||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
==Example Projects== |
==Example Projects== |
Revision as of 10:33, 20 April 2021
The Telink TLSR9518ADK80D is a Telink TLSR9518 evaluation board.
Features (selection)
- RISC-V 32Bit MCU
- 2MB on board QSPI flash
- Micro USB-B 1.1
- Line-In
- On board LED
- external debug connector pins
For further information please refer to the Telink TLSR9 wiki page
Setting up with J-Link
The Telink TLSR9518ADK80D evaluation board comes with an external JTAG debug connector (6 pins: TDI, TDO, TCK, TMS, GND, VBUS). To set the board up with J-Link, the following steps are required:
-
Connect the J-Link to the evaluation board, using jumper wires as follows at connector J56:
Pin RP Pico Pin J-Link Signal "TL PE4 TDI" 5 TDI "TL PE5 TDO" 13 TDO "TL PE7 TCK" 9 TCK "TL PE6 TMS" 7 TMS "DEBUG" "GND" 4 GND "VBUS" 1 VTref
Note: For a more reliable, simpler solution, the SEGGER Flying Wire Adapter is recommended.
Example Projects
TBD