Difference between revisions of "NXP PNEV76FAMA"
(→Preparing for J-Link) |
|||
(5 intermediate revisions by one other user not shown) | |||
Line 1: | Line 1: | ||
+ | [[Category:Evalboards]] |
||
__TOC__ |
__TOC__ |
||
− | This article describes specifics for the NXP PNEV76FAMA evaluation board. It can be used to test & verify PN76 device support with J-Link. |
+ | This article describes specifics for the NXP PNEV76FAMA evaluation board. It can be used to test & verify [[NXP PN76 |PN76]] device support with J-Link. |
[[File:NXP_PNEV76FAMA.jpeg|450px]] |
[[File:NXP_PNEV76FAMA.jpeg|450px]] |
||
Line 11: | Line 12: | ||
*For board REV D remove jumper J20 3-4 and connect pin 4 of J20 to any ground e.g. TP4. Keep J25 open. |
*For board REV D remove jumper J20 3-4 and connect pin 4 of J20 to any ground e.g. TP4. Keep J25 open. |
||
*Connect the J-Link to the debug connector (J21) |
*Connect the J-Link to the debug connector (J21) |
||
− | *Power the board via |
+ | *Power the board via USB (J5) |
− | Afterwards, the board should look similar to this: |
+ | Afterwards, the board should look similar to this:<br> |
[[File:NXP_PNEV76FAMA_Wired.PNG|400px]] |
[[File:NXP_PNEV76FAMA_Wired.PNG|400px]] |
||
− | + | Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
|
[[File:NXP_PNEV76FAMA_Connect.PNG|400px]] |
[[File:NXP_PNEV76FAMA_Connect.PNG|400px]] |
||
== Example Project== |
== Example Project== |
||
− | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the NXP |
+ | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the NXP PNEV76FAMA. It is a simple Hello World sample linked into the internal flash. |
====SETUP==== |
====SETUP==== |
||
*J-Link software: V7.65b |
*J-Link software: V7.65b |
Latest revision as of 15:26, 8 May 2024
This article describes specifics for the NXP PNEV76FAMA evaluation board. It can be used to test & verify PN76 device support with J-Link.
Minimum requirements
- J-Link software V7.65b or later
Preparing for J-Link
- For board REV D remove jumper J20 3-4 and connect pin 4 of J20 to any ground e.g. TP4. Keep J25 open.
- Connect the J-Link to the debug connector (J21)
- Power the board via USB (J5)
Afterwards, the board should look similar to this:
Verify the Connection with e.g. J-Link Commander. The output should look as follows:
Example Project
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the NXP PNEV76FAMA. It is a simple Hello World sample linked into the internal flash.
SETUP
- J-Link software: V7.65b
- Embedded Studio: V6.22
- Hardware: NXP PNEV76FAMA
- Link: File:NXP PNEV76FAMA ES V622.zip