Difference between revisions of "Infineon PMG1"
(→Connect) |
(→Connect) |
||
| Line 21: | Line 21: | ||
===Connect=== |
===Connect=== |
||
The connect sequence of PMG1 devices is very time critical and is performed from the J-Link's side directly in either one of these 2 modes:<br> |
The connect sequence of PMG1 devices is very time critical and is performed from the J-Link's side directly in either one of these 2 modes:<br> |
||
| + | * Reset mode: <br> J-Link toggles the XRES line and then sends SWD commands.<br>Reset mode is not supported by PMG1-S0 devices because they do not have an XRES pin.<br> |
||
| − | * Reset mode: <br> |
||
| + | * Power Cycle mode:<br> J-Link powers on the target and then starts sending the SWD commands.<br>Therefore the target device needs to be supplied via Pin 19 of the J-Link and Pin 1 also needs to be connected to pin 19 of the J-Link.<br>Make sure to set VSupply (pin 19) correctly before connecting it to the target board.<br>This is the only mode supported by PMG1-S0 devices.<br> |
||
| − | ** J-Link toggles the XRES line and then sends SWD commands. |
||
| − | ** Reset mode is not supported by PMG1-S0 devices because they do not have an XRES pin. |
||
| − | * Power Cycle mode:<br> |
||
| − | ** J-Link powers on the target and then starts sending the SWD commands. <br> |
||
| − | ** Therefore the target device needs to be supplied via Pin 19 of the J-Link and Pin 1 also needs to be connected to pin 19 of the J-Link.<br> |
||
| − | ** Make sure to set VSupply (pin 19) correctly before connecting it to the target board. <br> |
||
| − | ** This is the only mode supported by PMG1-S0 devices.<br> |
||
| − | |||
A device with reconfigured SWD pins runs automatically the acquire sequence to get control of the SWD pins for debugging back.<br> |
A device with reconfigured SWD pins runs automatically the acquire sequence to get control of the SWD pins for debugging back.<br> |
||
Revision as of 12:34, 13 May 2024
The Infineon PMG1 is a family of high-voltage USB PD MCUs with Arm® Cortex®-M0/Cortex-M0+ CPU.
Contents
Flash Banks
Internal Flash
| Subfamily | Flash Bank | Base address | Size | J-Link Support |
|---|---|---|---|---|
| PMG1-B1 | Internal Flash | 0x00000000 | 128 KB | 
|
| PMG1-S0 | Internal Flash | 0x00000000 | 64 KB |
|
Watchdog Handling
- The device has a watchdog WDT.
- The watchdog is not fed during flash programming.
Device Specific Handling
Connect
The connect sequence of PMG1 devices is very time critical and is performed from the J-Link's side directly in either one of these 2 modes:
- Reset mode:
J-Link toggles the XRES line and then sends SWD commands.
Reset mode is not supported by PMG1-S0 devices because they do not have an XRES pin. - Power Cycle mode:
J-Link powers on the target and then starts sending the SWD commands.
Therefore the target device needs to be supplied via Pin 19 of the J-Link and Pin 1 also needs to be connected to pin 19 of the J-Link.
Make sure to set VSupply (pin 19) correctly before connecting it to the target board.
This is the only mode supported by PMG1-S0 devices.
A device with reconfigured SWD pins runs automatically the acquire sequence to get control of the SWD pins for debugging back.
Reset
- The device uses custom reset via AIRCR.SYSRESETREQ and halt at application entry point.
Limitations
Attach
Attach is not supported because the J-Link resets the device on connect.
