Difference between revisions of "HSXP HK32F030M"
(Created page with "__TOC__ This article describes specifics for the HSXP_HK32F030M evaluation board. It can be used to test & verify HK32F03xx series device support. File:HSXP_HK32F030M.jpg|...") |
(→Preparing for J-Link) |
||
(3 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
__TOC__ |
__TOC__ |
||
− | This article describes specifics for the HSXP_HK32F030M evaluation board. It can be used to test & verify HK32F03xx series device support. |
+ | This article describes specifics for the HSXP_HK32F030M/0301M evaluation board. It can be used to test & verify HK32F03xx series device support. |
[[File:HSXP_HK32F030M.jpg|450px]] |
[[File:HSXP_HK32F030M.jpg|450px]] |
||
Line 9: | Line 9: | ||
== Preparing for J-Link == |
== Preparing for J-Link == |
||
− | *Connect the J-Link to the SWD header (CN1) on the right side |
+ | *Connect the J-Link to the SWD header (CN1) on the right side with jumper cables. |
+ | {| class="wikitable" |
||
+ | |- |
||
+ | ! Board Pin !! J-Link Pin |
||
+ | |- |
||
+ | | GND || GND (PIN4) |
||
+ | |- |
||
+ | | 3.3V || VTref (PIN1) |
||
+ | |- |
||
+ | | DIO || SWDIO (PIN7) |
||
+ | |- |
||
+ | | CLK || SWDCLK (PIN9) |
||
+ | |- |
||
+ | | RST || RESET (PIN15) |
||
+ | |} |
||
*Power the board via the USB connector |
*Power the board via the USB connector |
||
== Example Project== |
== Example Project== |
||
− | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the |
+ | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the HSXP HK32F030M /HK32F0301M. It is a simple Hello World sample linked into the internal flash.<br> |
====SETUP==== |
====SETUP==== |
||
*J-Link software: V7.60c |
*J-Link software: V7.60c |
Latest revision as of 10:30, 10 January 2022
This article describes specifics for the HSXP_HK32F030M/0301M evaluation board. It can be used to test & verify HK32F03xx series device support.
Minimum requirements
- J-Link software V7.60c or later
Preparing for J-Link
- Connect the J-Link to the SWD header (CN1) on the right side with jumper cables.
Board Pin | J-Link Pin |
---|---|
GND | GND (PIN4) |
3.3V | VTref (PIN1) |
DIO | SWDIO (PIN7) |
CLK | SWDCLK (PIN9) |
RST | RESET (PIN15) |
- Power the board via the USB connector
Example Project
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the HSXP HK32F030M /HK32F0301M. It is a simple Hello World sample linked into the internal flash.
SETUP
- J-Link software: V7.60c
- Embedded Studio: V5.50d
- Hardware: HSXP HK32F030M /HK32F0301M
- Link: File:HSXP HK32F030xx TestProject ES V550d.zip