Difference between revisions of "NXP JN5189-DK006"
(→Preparing for J-Link) |
|||
Line 1: | Line 1: | ||
__TOC__ |
__TOC__ |
||
− | This article describes specifics for the NXP JN5189-DK006 |
+ | This article describes specifics for the NXP JN5189-DK006 evaluation board. |
[[File:SiPeed_Lingan_Nano.jpg|250px]] |
[[File:SiPeed_Lingan_Nano.jpg|250px]] |
||
Line 19: | Line 19: | ||
=== Example projects for SEGGER Embedded Studio=== |
=== Example projects for SEGGER Embedded Studio=== |
||
− | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the |
+ | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the NXP JN5189-DK006. It is a simple Hello World sample and can be downloaded here: |
− | [[Media: |
+ | [[Media: NXP_QN9090_TestProject_ES_V452b.zip | Hello World sample ]] |
− | __TOC__ |
||
− | |||
− | This article describes specifics for the SiPeed Longan Nano board based on a GigaDevice GD32VF103CB. |
||
− | |||
− | [[File:SiPeed_Lingan_Nano.jpg|250px]] |
||
− | |||
− | == Minimum requirements == |
||
− | * RISC-V is supported by current J-Link models. In case of doubt, please check [[Software and Hardware Features Overview | Overview about which models / revisions support RISC-V]] |
||
− | * Embedded Studio Version 4.30 or later |
||
− | * J-Link software V6.54a or later |
||
− | |||
− | == Preparing for J-Link == |
||
− | The SiPeed Longan Nano does not come with a standard debug connector but populates the debug JTAG signals on 6 pads that can be found on the opposite of the USB-C interface. Therefore, it can be manually wired in case J-Link shall be connected to it. |
||
− | |||
− | The following guide will describe how the Longan Nano Board can be connected to your J-Link Base V10 or higher. Other J-Links might work as well but wiring might be slightly different. All needed information can be found in the probe related documentation. |
||
− | |||
− | * The Longan Nano board does not come with the pin header populated so first the pin headers need to be soldered to your board. |
||
− | * Now connect the board with e.g. jumperwires to your J-Link probe. |
||
− | * The following table shows how the Signals should be connected on both the board and [https://www.segger.com/products/debug-probes/j-link/technology/interface-description/ J-Link] side. |
||
− | |||
− | {| class="wikitable" |
||
− | |- |
||
− | ! J-Link 20 pin debug interface !! Pin on eval board pads |
||
− | |- |
||
− | | Pin 1 (VTref) || 3V3 |
||
− | |- |
||
− | | Pin 4 (GND) || GND |
||
− | |- |
||
− | | Pin 5 (TDI) || JTDI |
||
− | |- |
||
− | | Pin 7 (TMS) || JTMS |
||
− | |- |
||
− | | Pin 9 (TCK) || JTCK |
||
− | |- |
||
− | | Pin 13 (TDO) || JTDO |
||
− | |- |
||
− | |} |
||
− | The resulting connection will then look like this: |
||
− | |||
− | [[File:Longan_Nano.png|450px]] |
||
− | * Power the board via the USB-C port. |
||
− | * Verify the Connection with e.g. [https://wiki.segger.com/J-Link_cannot_connect_to_the_CPU#Verify_functionality_using_J-Link_Commander J-Link Commander]. The output should look as follows: |
||
− | |||
− | [[File:GD32VF1xx_Connect.PNG|400px]] |
||
− | |||
− | == Debugging in SEGGER Embedded Studio == |
||
− | |||
− | === Example projects for SEGGER Embedded Studio=== |
||
− | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the Longan Nano board. It is a simple Hello World sample and can be downloaded here: |
||
− | |||
− | [[Media: GD32VF1xx_Hello_World.zip | Hello World sample ]] |
Revision as of 11:31, 5 May 2020
Contents
This article describes specifics for the NXP JN5189-DK006 evaluation board.
Minimum requirements
- J-Link software V6.74 or later
Preparing for J-Link
- Make sure that you install the correct "Upgrade Board"
- Connect the J-Link to the SWD header (P1)
- Power the board via external power supply / power jack (J4)
- Verify the Connection with e.g. J-Link Commander. The output should look as follows:
Debugging in SEGGER Embedded Studio
Example projects for SEGGER Embedded Studio
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the NXP JN5189-DK006. It is a simple Hello World sample and can be downloaded here: