Difference between revisions of "Renesas Evaluation Kit RE01 1500KB"
| (4 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
__TOC__ |
__TOC__ |
||
| + | This article describes specifics for the Renesas Evaluation Kit RE01 1500KB. |
||
| + | |||
| + | [[File:Renesas_Evaluation_Kit_RE01_1500KB.jpg|450px]] |
||
= QSPI Flash Programming Support = |
= QSPI Flash Programming Support = |
||
Before continuing with this article, please read the generic article about QSPI flash programming support on Renesas RE01 devices ([[Renesas_RE01#QSPI_support|Renesas RE01 QSPI]]). The pinout used on the ''Evaluation Kit RE01 1500KB'', is given below. |
Before continuing with this article, please read the generic article about QSPI flash programming support on Renesas RE01 devices ([[Renesas_RE01#QSPI_support|Renesas RE01 QSPI]]). The pinout used on the ''Evaluation Kit RE01 1500KB'', is given below. |
||
| − | |||
| − | ==== Embedded Studio example project ==== |
||
| − | The example project contains a simple RTT application which is linked into the (Q)SPI flash memory region @ address 0x60000000. It runs out-of-the-box. Please note, that SEGGER Embedded Studio for ARM must at least use the J-Link DLL version V6.71c, which supports the QSPI flash. |
||
| − | |||
| − | The project has been tested with SEGGER Embedded Studio for ARM 4.52. |
||
==== Quad-SPI Interface Pins ==== |
==== Quad-SPI Interface Pins ==== |
||
| Line 23: | Line 21: | ||
| QIO1_A || P015 |
| QIO1_A || P015 |
||
|} |
|} |
||
| + | |||
| + | ==== Example Project ==== |
||
| + | The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the Renesas Evaluation Kit RE01 1500KB. It is a simple [[RTT]] Hello World sample linked into the internal flash and the QSPI flash. |
||
| + | One function (_FuncInQSPI) is located in the QSPI-Flash. |
||
| + | |||
| + | ===== Requirements ===== |
||
| + | * J-Link Software V6.71c or above |
||
| + | * Embedded Studio: V4.52 or above |
||
| + | * Hardware: Renesas Evaluation Kit RE01 1500KB |
||
| + | * Link: [[File:Renesas_RE01_1500KB_EVK_QSPI_SES_Example.zip]] |
||
Latest revision as of 13:57, 5 May 2020
Contents
This article describes specifics for the Renesas Evaluation Kit RE01 1500KB.
QSPI Flash Programming Support
Before continuing with this article, please read the generic article about QSPI flash programming support on Renesas RE01 devices (Renesas RE01 QSPI). The pinout used on the Evaluation Kit RE01 1500KB, is given below.
Quad-SPI Interface Pins
The Renesas Evaluation Kit RE01 1500KB uses the following port pins to interface the (Q)SPI flash.
| Alternate function | Pin |
|---|---|
| QSPCLK_A | P602 |
| QSSL_A | P601 |
| QIO0_A | P500 |
| QIO1_A | P015 |
Example Project
The following example project was created with the SEGGER Embedded Studio project wizard and runs out-of-the-box on the Renesas Evaluation Kit RE01 1500KB. It is a simple RTT Hello World sample linked into the internal flash and the QSPI flash. One function (_FuncInQSPI) is located in the QSPI-Flash.
Requirements
- J-Link Software V6.71c or above
- Embedded Studio: V4.52 or above
- Hardware: Renesas Evaluation Kit RE01 1500KB
- Link: File:Renesas RE01 1500KB EVK QSPI SES Example.zip
